Hyd Front Furrow.
Hyd Vari Width.
Hyd Auto Rest.
Press Arm.
Very little use – done less in its lifetime than some do in a season!
]]>Rollover Sheet.
Front Grille / Window.
Grain Hatch.
Only been a couple of days a year.
]]>
W52 Bodies.
Hyd Variwidth.
Hyd Depth Wheel.
Rated to 450hp.
Press Arm.
CAT 3.
Been on some kind working land in South Lincolnshire.
In very good condition.
Video shows it working this week.
]]>Only ploughed 400acres.
Hyd Front Furrow.
Shearbolt.
The pictures say it all!!!!
]]>£2950 for Grab Bucket.
]]>Dealer Serviced.
Cut 200acres last year.
1256 Drum hours, 1780 Engine hours.
2010 5.5m 618R Header with Trailer.
Combine is a 2009 build first registered Aug. ’12.
With current owner driver who is retiring since 2016.
10 years service history.
2wd.
]]>Air Brakes.
4 Manual Spools.
Warranty to 3000hrs or 23/9/28.
No Guidance.
]]>50acres/year for last few years.
Fixed sieves – Self Levelling Actuator been replace with flat plate as in picture.
Recent new rear tyres.
24ft Header with trailer.
Onboard Compressor for blowing off.
Annually serviced by independent mechanic.
]]>Bought in a batch of 20 by local NH Dealer in 2020.
First registered 2021 – 1 owner.
Dealer serviced – just had 1000hr service.
JCB Q-Fit Headstock with Hydraulic Locking Pins.
3.7t lift. 7m reach.
144hp.
40kph.
6 Speed Powershift.
Reverser Fan.
]]>Manual Furrow Width.
DD Bodies.
Press Arm.
Hyd. Front Furrow.
Straight plough.
]]>5300 bales since last service.
Maybe not the prettiest but runs quiet and has not had its back broken and welded up!
Weigher.
]]>Just been through workshop, new blades and clutch discs where needed.
]]>The pictures show as it came in.
Just been serviced including new Crank Bearings.
Comes with C1000 Monitor and an endless future of happy baling!
]]>AdBlue Tank.
]]>
2.25m working width.
Straight condition.
]]>In ex demo condition.
]]>Press Arm.
Vogel and Noot Furrow Press also available.
]]>In very good order – not been over horsepowered.
Makes a 4 string double knot bale.
No weigher to try and calibrate!
]]>Cousins Wearing Metal.
Set at 30″ apart.
45cm Hyd Packer.
Recently professionally resprayed.
In very good order.
]]>Reversing camera & auger camera & lights. Selection of spare parts, a tidy high spec chaser.
Hyd Brakes.
]]>17 Front Disc @ 23″.
15 Rear Discs @ 27″.
A very tight set of discs.
]]>Sprung 8 Stud Axles.
Hyd Door.
Tidy.
]]>Can load up to 4 of 120×90 rectangular bales or 3 round bales.
The three lower tines provided as standard are mounted on an articulated base to instantly switch to fixed, floating and transport positions.
JCB Q Fit Brackets.
]]>20.8R38 and 16.9R28
16 Clamps.
70% Tread
1 of the rears has small slits around the outside as circled in blue.
]]>Quantron S2 Control Box. 1240ha.
Seedflex coulters that are as good as new.
New p/h tines 50 acres ago.
New following harrow tines.
Stands for removing drill.
]]>5 discs with 10 blades
Robust centre pivot for mower deck.
Shaft driven deck.
Vertical fold.
]]>
Working width 2.8 metres
Hydraulic side shift with 400mm offset
36 Heavy duty whale head flails, 60mm cut capacity
Double skin front Canopy.
Heavy duty uprated gearbox, six belt pulley system. with overrun protection
Front protection flaps, 194mm full width rear adjustable Roller
Replaceable bolt on skids
Can be used in 540 or 1000RPM
]]>Belt can turn eitherway.
1 single act spool with freeflow return needed for belt motor and another single acting for top roller lift ram.
]]>30kph. Manual Forward/Reverse Shuttle.
2 Spools.
Option of Turf Tyres.
]]>
New wings fitted.
Discs and Twin Crumblers.
No welding.
Very straight for age of machine.
]]>
Rotorfeed CropCutter.
Weigher.
Annually dealer serviced.
Makes a 120 x 90 bale.
Runs on ISOBUS – no monitor.
]]>
18ft Header with Trailer.
Runs up fine.
]]>
Rubber blade.
Comes with storage frame on Castor Wheels.
]]>Rear linkage with A-frame Drawbar.
Only been on a 200hp tractor.
]]>
Number 8 Bodies.
Manual Variwidth.
Good Metal – new points, shares and shins – tungsten tipped.
Onland.
]]>Good metal all round.
Works well.
]]>Manual Variwidth.
Excellent wearing metal all round.
]]>No clumative counter but I would say it is under 10,000 bales.
Rotor Feed but no knives.
Runs up quiet.
Net wrap.
4ft Fixed Chamber roller Baler.
]]>Tips bales on side as they leave the Baler.
Makes picking up easier as strings are showing so don’t have to flip over to stack.
]]>220mm hub hole with 22mm stud holed.
420mm and 175mm off sets.
]]>
Very little use.
]]>Hydraulic Fold.
Heavy Duty 1/2 inch tines.
]]>The video shows TR300 working in wet 40ft swath throwing it out at an angle.
]]>These Grabs have been designed by ourselves to handle thousands of Big Square Bales per year. The bottom bale is spiked while the others above it are pulled back tight against the frame with the side claws. The top of the frame extends to allow upto 3 MF 2190 (Full Hesston) or equivilant bales to be safely handled.
The grab can also be used horizontally as you would a Flat 8 Grab.
For use on the road the Tine Bar folds back and the Tines are caught the Claws to leave minimum obstruction. The strong open Framework leaves excellent visibility for operator.
We have been using these Grabs for years and have not broken one yet!
Will also move Bale Bandit Packs.
Also make fixed Grab for 3 Hesstons – see last 2 pictures on a Kramer.